Only Displayport working, no signal through HDMI, switched to 5060 ti from AMD

[prosetheus (Paul Phoenix)]

Hello!

This was difficult to google due to overlapping keywords with laptop users, so here we are.

I have a Ryzen 9800x3d, a MSI mobo, and recently switched my GPU from the 6900xt to the 5060 ti. I followed this guide:

GitHub - Comprehensive-Wall28/Nvidia-Fedora-Guide: A complete guide on getting Nvidia's Proprietary...

and was able to install the drivers and boot up just fine.

I have a 1440p monitor connected through DP and a 4k TV connected through HDMI. For some reason, through the Display settings, I cannot output or even activate the TV although everything works fine on the monitor.

And even while viewing the settings for the TV in the Fedora Display utility, it states in the Display settings that I can only select a max refresh rate of 30 Hz whereas it is a 4k 60 tv.

Even more weirdly, this is persistent stutter in the mouse movement and keyboard typing every few seconds while the TV is turned on as another display in settings as a display but not getting a signal at all.

Everything was working fine up until the GPU switch. Any idea how this issue can be resolved? Much thanks!

[computersavvy (Jeff V)]

We need a little more info.
The tv may require an hdmi 3.1 cable for the 60 hz refresh.
Some gpus will only support 30hz refresh at 4k on hdmi, but will support 60hz with DP.

Please post as preformatted text the output of the following commands.
dnf list --installed \*nvidia\*
lsmod | grep nvidia
inxi -Fzxx
modinfo -F version nvidia
modinfo -l nvidia

Of those commands the only one with large amount of output is inxi.

[gnwiii (George N. White III)]

@computersavvy

Of those commands the only one with large amount of output is inxi.

Where “large” is usually less than 200 lines.

[prosetheus (Paul Phoenix)]

Hey!

I’ve posted as preformatted text the output of the commands.

I’ll also add that this exact same setup was working without issues with the prior AMD GPU. Adding that because that removes cables from the issue (I hope, as they’re the same).

dnf list --installed *nvidia*

akmod-nvidia.x86_64                        3:580.142-2.fc43    <unknown>
kmod-nvidia-6.19.11-200.fc43.x86_64.x86_64 3:580.126.18-1.fc43 @commandline
kmod-nvidia-6.19.13-200.fc43.x86_64.x86_64 3:580.142-2.fc43    @commandline
nvidia-gpu-firmware.noarch                 20260410-1.fc43     <unknown>
nvidia-modprobe.x86_64                     3:580.142-1.fc43    <unknown>
nvidia-persistenced.x86_64                 3:580.142-1.fc43    <unknown>
nvidia-settings.x86_64                     3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia.x86_64                 3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-cuda.x86_64            3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-cuda-libs.i686         3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-cuda-libs.x86_64       3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-kmodsrc.x86_64         3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-libs.i686              3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-libs.x86_64            3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-power.x86_64           3:580.142-1.fc43    <unknown>

lsmod | grep nvidia

nvidia_uvm           4210688  0
nvidia_drm            159744  32
nvidia_modeset       2265088  12 nvidia_drm
nvidia              15904768  297 nvidia_uvm,nvidia_modeset
drm_ttm_helper         20480  2 amdgpu,nvidia_drm
video                  81920  2 amdgpu,nvidia_modeset

inxi -Fzxx

System:
  Kernel: 6.19.13-200.fc43.x86_64 arch: x86_64 bits: 64 compiler: gcc
    v: 15.2.1
  Desktop: GNOME v: 49.6 tk: GTK v: 3.24.52 wm: gnome-shell dm: GDM
    Distro: Fedora Linux 43 (Workstation Edition)
Machine:
  Type: Desktop Mobo: Micro-Star model: PRO X870E-P WIFI (MS-7E70) v: 2.0
    serial: <superuser required> Firmware: UEFI vendor: American Megatrends LLC.
    v: 2.A40 date: 01/20/2026
CPU:
  Info: 8-core model: AMD Ryzen 7 9800X3D bits: 64 type: MT MCP arch: Zen 5
    rev: 0 cache: L1: 640 KiB L2: 8 MiB L3: 96 MiB
  Speed (MHz): avg: 4563 min/max: 603/5272 boost: enabled cores: 1: 4563
    2: 4563 3: 4563 4: 4563 5: 4563 6: 4563 7: 4563 8: 4563 9: 4563 10: 4563
    11: 4563 12: 4563 13: 4563 14: 4563 15: 4563 16: 4563 bogomips: 150399
  Flags-basic: avx avx2 ht lm nx pae sse sse2 sse3 sse4_1 sse4_2 sse4a
    ssse3 svm
Graphics:
  Device-1: NVIDIA GB206 [GeForce RTX 5060 Ti] vendor: ZOTAC driver: nvidia
    v: 580.142 arch: Lovelace pcie: speed: 2.5 GT/s lanes: 8 ports: active: DP-6
    off: HDMI-A-2 empty: DP-4,DP-5 bus-ID: 01:00.0 chip-ID: 10de:2d04
  Device-2: Advanced Micro Devices [AMD/ATI] Granite Ridge [Radeon Graphics]
    vendor: Micro-Star MSI driver: amdgpu v: kernel arch: RDNA-2 pcie:
    speed: 16 GT/s lanes: 16 ports: active: none empty: DP-1, DP-2, DP-3,
    HDMI-A-1, Writeback-1 bus-ID: 7a:00.0 chip-ID: 1002:13c0 temp: 42.0 C
  Display: wayland server: Xwayland v: 24.1.10 compositor: gnome-shell
    driver: gpu: nv_platform,nvidia,nvidia-nvswitch display-ID: 0
  Monitor-1: DP-6 model: XG27ACS res: 2560x1440 dpi: 109 diag: 685mm (27")
  Monitor-2: HDMI-A-2 model: Samsung res: 3840x2160 dpi: 103
    diag: 1093mm (43")
  API: OpenGL v: 4.6.0 vendor: nvidia v: 580.142 glx-v: 1.4
    direct-render: yes renderer: NVIDIA GeForce RTX 5060 Ti/PCIe/SSE2
    display-ID: :0.0
  API: Vulkan v: 1.4.341 surfaces: N/A device: 0 type: discrete-gpu
    driver: nvidia device-ID: 10de:2d04 device: 1 type: integrated-gpu
    driver: mesa radv device-ID: 1002:13c0 device: 2 type: cpu
    driver: mesa llvmpipe device-ID: 10005:0000
  API: EGL Message: EGL data requires eglinfo. Check --recommends.
  Info: Tools: api: clinfo, glxinfo, vulkaninfo gpu: lact, nvidia-settings,
    nvidia-smi x11: xdriinfo, xdpyinfo, xprop, xrandr
Audio:
  Device-1: NVIDIA GB206 High Definition Audio driver: snd_hda_intel v: kernel
    pcie: speed: 32 GT/s lanes: 8 bus-ID: 01:00.1 chip-ID: 10de:22eb
  Device-2: Advanced Micro Devices [AMD/ATI] Radeon High Definition Audio
    vendor: Micro-Star MSI driver: snd_hda_intel v: kernel pcie: speed: 16 GT/s
    lanes: 16 bus-ID: 7a:00.1 chip-ID: 1002:1640
  Device-3: Advanced Micro Devices [AMD] Ryzen HD Audio
    vendor: Micro-Star MSI driver: snd_hda_intel v: kernel pcie: speed: 16 GT/s
    lanes: 16 bus-ID: 7a:00.6 chip-ID: 1022:15e3
  API: ALSA v: k6.19.13-200.fc43.x86_64 status: kernel-api
  Server-1: PipeWire v: 1.4.11 status: active with: 1: pipewire-pulse
    status: active 2: wireplumber status: active 3: pipewire-alsa type: plugin
    4: pw-jack type: plugin
Network:
  Device-1: Realtek RTL8126 5GbE vendor: Micro-Star MSI driver: r8169
    v: kernel pcie: speed: 8 GT/s lanes: 1 port: e000 bus-ID: 0e:00.0
    chip-ID: 10ec:8126
  IF: enp14s0 state: up speed: 1000 Mbps duplex: full mac: <filter>
  Device-2: Qualcomm WCN785x Wi-Fi 7 320MHz 2x2 [FastConnect 7800]
    vendor: Foxconn Band Simultaneous Wireless driver: ath12k_pci v: N/A pcie:
    speed: 8 GT/s lanes: 1 bus-ID: 0f:00.0 chip-ID: 17cb:1107
  IF: wlp15s0 state: up mac: <filter>
  IF-ID-1: docker0 state: down mac: <filter>
Bluetooth:
  Device-1: Foxconn / Hon Hai driver: btusb v: 0.8 type: USB rev: 1.1
    speed: 12 Mb/s lanes: 1 bus-ID: 3-6:2 chip-ID: 0489:e10a
  Report: btmgmt ID: hci0 rfk-id: 0 state: up address: <filter> bt-v: 5.3
    lmp-v: 12

modinfo -F version nvidia

580.142

modinfo -l nvidia

Dual MIT/GPL

[computersavvy (Jeff V)]

It appears that nvidia may be properly installed, but we cannot tell what repo the packages were installed from.
The output of the dnf command should look like this, and your attempt to paste preformatted text has cut off the right end of every line for dnf and many lines for inxi.

$ dnf list --installed \*nvidia\*
Installed packages
akmod-nvidia.x86_64                        3:580.142-2.fc43 rpmfusion-nonfree-updates
kmod-nvidia-6.19.11-200.fc43.x86_64.x86_64 3:580.142-2.fc43 @commandline
kmod-nvidia-6.19.12-200.fc43.x86_64.x86_64 3:580.142-2.fc43 @commandline
kmod-nvidia-6.19.13-200.fc43.x86_64.x86_64 3:580.142-2.fc43 @commandline
nvidia-gpu-firmware.noarch                 20260410-1.fc43  updates
nvidia-modprobe.x86_64                     3:580.142-1.fc43 rpmfusion-nonfree-updates
nvidia-persistenced.x86_64                 3:580.142-1.fc43 rpmfusion-nonfree-updates
nvidia-settings.x86_64                     3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia.x86_64                 3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-cuda.x86_64            3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-cuda-libs.i686         3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-cuda-libs.x86_64       3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-kmodsrc.x86_64         3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-libs.i686              3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-libs.x86_64            3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-power.x86_64           3:580.142-1.fc43 rpmfusion-nonfree-updates
xorg-x11-drv-nvidia-xorg-libs.x86_64       3:580.142-1.fc43 rpmfusion-nonfree-updates

Preformatted text is done by pasting the data copied from your screen then highlight the new text and click the </> button on the toolbar of this text entry window. It retains the formatting and provides the scroll bars to view it.

Inxi should look similar to this

$ inxi -Fzxx
System:
  Kernel: 6.19.12-200.fc43.x86_64 arch: x86_64 bits: 64 compiler: gcc
    v: 15.2.1
  Desktop: GNOME v: 49.6 tk: GTK v: 3.24.52 wm: gnome-shell dm: GDM
    Distro: Fedora Linux 43 (Workstation Edition)
Machine:
  Type: Desktop Mobo: ASRock model: B550M Pro4 serial: <superuser required>
    Firmware: UEFI vendor: American Megatrends LLC. v: L2.71 date: 04/14/2023
Battery:
  Device-1: hidpp_battery_27 model: Logitech MX Ergo Multi-Device Trackball
    serial: <filter> charge: 55% (should be ignored) status: discharging
  Device-2: hidpp_battery_28 model: Logitech K350 serial: <filter>
    charge: 70% (should be ignored) status: discharging
CPU:
  Info: 8-core model: AMD Ryzen 7 5700X bits: 64 type: MT MCP arch: Zen 3+
    rev: 2 cache: L1: 512 KiB L2: 4 MiB L3: 32 MiB
  Speed (MHz): avg: 3802 min/max: 562/4666 boost: enabled cores: 1: 3802
    2: 3802 3: 3802 4: 3802 5: 3802 6: 3802 7: 3802 8: 3802 9: 3802 10: 3802
    11: 3802 12: 3802 13: 3802 14: 3802 15: 3802 16: 3802 bogomips: 108591
  Flags-basic: avx avx2 ht lm nx pae sse sse2 sse3 sse4_1 sse4_2 sse4a
    ssse3 svm
Graphics:
  Device-1: NVIDIA GA106 [Geforce RTX 3050] vendor: Micro-Star MSI
    driver: nvidia v: 580.142 arch: Ampere pcie: speed: 16 GT/s lanes: 8 ports:
    active: DP-1 empty: DP-2,DP-3,HDMI-A-1 bus-ID: 06:00.0 chip-ID: 10de:2507
  Device-2: ARC Camera driver: snd-usb-audio,uvcvideo type: USB rev: 2.0
    speed: 480 Mb/s lanes: 1 bus-ID: 3-2.3:4 chip-ID: 05a3:9331
  Display: wayland server: X.org v: 1.21.1.22 with: Xwayland v: 24.1.10
    compositor: gnome-shell driver: X: loaded: modesetting,nvidia
    alternate: fbdev,nouveau,nv,vesa gpu: nv_platform,nvidia,nvidia-nvswitch
    display-ID: 0
  Monitor-1: DP-1 model: LG (GoldStar) TV SSCR2 res: 3840x2160 hz: 30
    dpi: 61 diag: 1836mm (72.3")
  API: EGL v: 1.5 platforms: device: 0 drv: nvidia device: 2 drv: swrast
    gbm: drv: nvidia surfaceless: drv: nvidia wayland: drv: nvidia x11:
    drv: nvidia inactive: device-1
  API: OpenGL v: 4.6.0 compat-v: 4.5 vendor: nvidia mesa v: 580.142
    glx-v: 1.4 direct-render: yes renderer: NVIDIA GeForce RTX 3050/PCIe/SSE2
    display-ID: :0.0
  API: Vulkan v: 1.4.341 surfaces: N/A device: 0 type: discrete-gpu
    driver: nvidia device-ID: 10de:2507 device: 1 type: cpu
    driver: mesa llvmpipe device-ID: 10005:0000
  Info: Tools: api: eglinfo, glxinfo, vulkaninfo de: gnome-monitor-config
    gpu: nvidia-settings,nvidia-smi wl: wayland-info,wlr-randr x11: xdriinfo,
    xdpyinfo, xprop, xrandr
Audio:
  Device-1: NVIDIA GA106 High Definition Audio vendor: Micro-Star MSI
    driver: snd_hda_intel v: kernel pcie: speed: 16 GT/s lanes: 8
    bus-ID: 06:00.1 chip-ID: 10de:228e
  Device-2: Advanced Micro Devices [AMD] Starship/Matisse HD Audio
    vendor: ASRock driver: snd_hda_intel v: kernel pcie: speed: 16 GT/s
    lanes: 16 bus-ID: 08:00.4 chip-ID: 1022:1487
  Device-3: C-Media USB Audio Device
    driver: hid-generic,snd-usb-audio,usbhid type: USB rev: 1.1 speed: 12 Mb/s
    lanes: 1 bus-ID: 1-5.2:9 chip-ID: 0d8c:0012
  Device-4: ARC Camera driver: snd-usb-audio,uvcvideo type: USB rev: 2.0
    speed: 480 Mb/s lanes: 1 bus-ID: 3-2.3:4 chip-ID: 05a3:9331
  API: ALSA v: k6.19.12-200.fc43.x86_64 status: kernel-api
  Server-1: JACK v: 1.9.22 status: off
  Server-2: PipeWire v: 1.4.11 status: active with: 1: pipewire-pulse
    status: active 2: wireplumber status: active 3: pipewire-alsa type: plugin
    4: pw-jack type: plugin
Network:
  Device-1: Realtek RTL8111/8168/8211/8411 PCI Express Gigabit Ethernet
    vendor: ASRock driver: r8169 v: kernel pcie: speed: 2.5 GT/s lanes: 1
    port: f000 bus-ID: 04:00.0 chip-ID: 10ec:8168
  IF: enp4s0 state: down mac: <filter>
  Device-2: Intel Wi-Fi 6E AX210/AX1675 2x2 [Typhoon Peak] driver: iwlwifi
    v: kernel pcie: speed: 5 GT/s lanes: 1 bus-ID: 05:00.0 chip-ID: 8086:2725
  IF: wlp5s0 state: up mac: <filter>
  IF-ID-1: virbr0 state: down mac: <filter>
Bluetooth:
  Device-1: Intel AX210 Bluetooth driver: btusb v: 0.8 type: USB rev: 2.0
    speed: 12 Mb/s lanes: 1 bus-ID: 1-9:10 chip-ID: 8087:0032
  Report: btmgmt ID: hci0 rfk-id: 0 state: up address: <filter> bt-v: 5.4
    lmp-v: 13
RAID:
  Device-1: md127 type: mdraid level: raid-5 status: active size: 7.28 TiB
  Info: report: 3/3 UUU blocks: 7813772288 chunk-size: 512k
    super-blocks: 1.2 algorithm: 2
  Components: Online: 0: sda 1: sdc 3: sdd
Drives:
  Local Storage: total: raw: 20.01 TiB usable: 16.37 TiB
    used: 6.39 TiB (39.1%)
  ID-1: /dev/nvme0n1 vendor: Crucial model: CT2000P5PSSD8 size: 1.82 TiB
    speed: 63.2 Gb/s lanes: 4 serial: <filter> temp: 55.9 C
  ID-2: /dev/sda vendor: Seagate model: ST4000VN008-2DR166 size: 3.64 TiB
    speed: 6.0 Gb/s serial: <filter> temp: 39 C
  ID-3: /dev/sdb vendor: Seagate model: ST8000VN004-2M2101 size: 7.28 TiB
    speed: 6.0 Gb/s serial: <filter>
  ID-4: /dev/sdc vendor: Seagate model: ST4000VN008-2DR166 size: 3.64 TiB
    speed: 6.0 Gb/s serial: <filter> temp: 38 C
  ID-5: /dev/sdd vendor: Seagate model: ST4000VN008-2DR166 size: 3.64 TiB
    speed: 6.0 Gb/s serial: <filter> temp: 38 C
Partition:
  ID-1: / size: 392.65 GiB used: 118.87 GiB (30.3%) fs: ext4 dev: /dev/dm-0
    mapped: fedora_root-root
  ID-2: /boot size: 1.14 GiB used: 512.5 MiB (44.1%) fs: ext4
    dev: /dev/nvme0n1p2
  ID-3: /boot/efi size: 490 MiB used: 19.3 MiB (3.9%) fs: vfat
    dev: /dev/nvme0n1p1
  ID-4: /home size: 7.22 TiB used: 6.28 TiB (87.0%) fs: ext4 dev: /dev/dm-1
    mapped: fedora_raid1-home
Swap:
  ID-1: swap-1 type: zram size: 8 GiB used: 56.8 MiB (0.7%) priority: 100
    dev: /dev/zram0
Sensors:
  System Temperatures: cpu: 79.8 C mobo: N/A
  Fan Speeds (rpm): N/A
Info:
  Memory: total: 32 GiB available: 31.25 GiB used: 6.29 GiB (20.1%)
  Processes: 460 Power: uptime: 7d 1h 14m wakeups: 0 Init: systemd v: 258
    default: graphical
  Packages: pm: rpm pkgs: N/A note: see --rpm pm: flatpak pkgs: 26
    Compilers: gcc: 15.2.1 Shell: Bash v: 5.3.0 running-in: ptyxis-agent
    inxi: 3.3.40

[anotheruser (Mark)]

@prosetheus

Graphics:
  Device-1: NVIDIA GB206 [GeForce RTX 5060 Ti] vendor: ZOTAC driver: nvidia
    v: 580.142 arch: Lovelace pcie: speed: 2.5 GT/s lanes: 8 ports: active: DP-6
    **off: HDMI-A-2** 

It seems that you’ve disabled the 2nd display in gnome-settings…

[prosetheus (Paul Phoenix)]

My bad. Reposting them

dnf list --installed *nvidia*

Installed packages
akmod-nvidia.x86_64                        3:580.142-2.fc43    <unknown>
kmod-nvidia-6.19.11-200.fc43.x86_64.x86_64 3:580.126.18-1.fc43 @commandline
kmod-nvidia-6.19.13-200.fc43.x86_64.x86_64 3:580.142-2.fc43    @commandline
nvidia-gpu-firmware.noarch                 20260410-1.fc43     <unknown>
nvidia-modprobe.x86_64                     3:580.142-1.fc43    <unknown>
nvidia-persistenced.x86_64                 3:580.142-1.fc43    <unknown>
nvidia-settings.x86_64                     3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia.x86_64                 3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-cuda.x86_64            3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-cuda-libs.i686         3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-cuda-libs.x86_64       3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-kmodsrc.x86_64         3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-libs.i686              3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-libs.x86_64            3:580.142-1.fc43    <unknown>
xorg-x11-drv-nvidia-power.x86_64           3:580.142-1.fc43    <unknown>

lsmod | grep nvidia

nvidia_uvm           4210688  0
nvidia_drm            159744  42
nvidia_modeset       2265088  11 nvidia_drm
nvidia              15904768  343 nvidia_uvm,nvidia_modeset
drm_ttm_helper         20480  2 amdgpu,nvidia_drm
video                  81920  2 amdgpu,nvidia_modeset

inxi -Fzxx

System:
  Kernel: 6.19.13-200.fc43.x86_64 arch: x86_64 bits: 64 compiler: gcc
    v: 15.2.1
  Desktop: GNOME v: 49.6 tk: GTK v: 3.24.52 wm: gnome-shell dm: GDM
    Distro: Fedora Linux 43 (Workstation Edition)
Machine:
  Type: Desktop Mobo: Micro-Star model: PRO X870E-P WIFI (MS-7E70) v: 2.0
    serial: <superuser required> Firmware: UEFI vendor: American Megatrends LLC.
    v: 2.A40 date: 01/20/2026
CPU:
  Info: 8-core model: AMD Ryzen 7 9800X3D bits: 64 type: MT MCP arch: Zen 5
    rev: 0 cache: L1: 640 KiB L2: 8 MiB L3: 96 MiB
  Speed (MHz): avg: 4661 min/max: 603/5272 boost: enabled cores: 1: 4661
    2: 4661 3: 4661 4: 4661 5: 4661 6: 4661 7: 4661 8: 4661 9: 4661 10: 4661
    11: 4661 12: 4661 13: 4661 14: 4661 15: 4661 16: 4661 bogomips: 150399
  Flags-basic: avx avx2 ht lm nx pae sse sse2 sse3 sse4_1 sse4_2 sse4a
    ssse3 svm
Graphics:
  Device-1: NVIDIA GB206 [GeForce RTX 5060 Ti] vendor: ZOTAC driver: nvidia
    v: 580.142 arch: Lovelace pcie: speed: 2.5 GT/s lanes: 8 ports: active: DP-6
    off: HDMI-A-2 empty: DP-4,DP-5 bus-ID: 01:00.0 chip-ID: 10de:2d04
  Device-2: Advanced Micro Devices [AMD/ATI] Granite Ridge [Radeon Graphics]
    vendor: Micro-Star MSI driver: amdgpu v: kernel arch: RDNA-2 pcie:
    speed: 16 GT/s lanes: 16 ports: active: none empty: DP-1, DP-2, DP-3,
    HDMI-A-1, Writeback-1 bus-ID: 7a:00.0 chip-ID: 1002:13c0 temp: 42.0 C
  Display: wayland server: Xwayland v: 24.1.10 compositor: gnome-shell
    driver: gpu: nv_platform,nvidia,nvidia-nvswitch display-ID: 0
  Monitor-1: DP-6 model: XG27ACS res: 2560x1440 dpi: 109 diag: 685mm (27")
  Monitor-2: HDMI-A-2 model: Samsung res: 3840x2160 dpi: 103
    diag: 1093mm (43")
  API: OpenGL v: 4.6.0 vendor: nvidia v: 580.142 glx-v: 1.4
    direct-render: yes renderer: NVIDIA GeForce RTX 5060 Ti/PCIe/SSE2
    display-ID: :0.0
  API: Vulkan v: 1.4.341 surfaces: N/A device: 0 type: discrete-gpu
    driver: nvidia device-ID: 10de:2d04 device: 1 type: integrated-gpu
    driver: mesa radv device-ID: 1002:13c0 device: 2 type: cpu
    driver: mesa llvmpipe device-ID: 10005:0000
  API: EGL Message: EGL data requires eglinfo. Check --recommends.
  Info: Tools: api: clinfo, glxinfo, vulkaninfo gpu: lact, nvidia-settings,
    nvidia-smi x11: xdriinfo, xdpyinfo, xprop, xrandr
Audio:
  Device-1: NVIDIA GB206 High Definition Audio driver: snd_hda_intel v: kernel
    pcie: speed: 32 GT/s lanes: 8 bus-ID: 01:00.1 chip-ID: 10de:22eb
  Device-2: Advanced Micro Devices [AMD/ATI] Radeon High Definition Audio
    vendor: Micro-Star MSI driver: snd_hda_intel v: kernel pcie: speed: 16 GT/s
    lanes: 16 bus-ID: 7a:00.1 chip-ID: 1002:1640
  Device-3: Advanced Micro Devices [AMD] Ryzen HD Audio
    vendor: Micro-Star MSI driver: snd_hda_intel v: kernel pcie: speed: 16 GT/s
    lanes: 16 bus-ID: 7a:00.6 chip-ID: 1022:15e3
  API: ALSA v: k6.19.13-200.fc43.x86_64 status: kernel-api
  Server-1: PipeWire v: 1.4.11 status: active with: 1: pipewire-pulse
    status: active 2: wireplumber status: active 3: pipewire-alsa type: plugin
    4: pw-jack type: plugin
Network:
  Device-1: Realtek RTL8126 5GbE vendor: Micro-Star MSI driver: r8169
    v: kernel pcie: speed: 8 GT/s lanes: 1 port: e000 bus-ID: 0e:00.0
    chip-ID: 10ec:8126
  IF: enp14s0 state: up speed: 1000 Mbps duplex: full mac: <filter>
  Device-2: Qualcomm WCN785x Wi-Fi 7 320MHz 2x2 [FastConnect 7800]
    vendor: Foxconn Band Simultaneous Wireless driver: ath12k_pci v: N/A pcie:
    speed: 8 GT/s lanes: 1 bus-ID: 0f:00.0 chip-ID: 17cb:1107
  IF: wlp15s0 state: up mac: <filter>
  IF-ID-1: docker0 state: down mac: <filter>
Bluetooth:
  Device-1: Foxconn / Hon Hai driver: btusb v: 0.8 type: USB rev: 1.1
    speed: 12 Mb/s lanes: 1 bus-ID: 3-6:2 chip-ID: 0489:e10a
  Report: btmgmt ID: hci0 rfk-id: 0 state: up address: <filter> bt-v: 5.3
    lmp-v: 12
Drives:
  Local Storage: total: 22.3 TiB used: 10.6 TiB (47.5%)
  ID-1: /dev/nvme0n1 vendor: A-Data model: SX8200PNP size: 476.94 GiB
    speed: 31.6 Gb/s lanes: 4 serial: <filter> temp: 31.9 C
  ID-2: /dev/nvme1n1 vendor: Western Digital model: WD BLACK SN850X 4000GB
    size: 3.64 TiB speed: 63.2 Gb/s lanes: 4 serial: <filter> temp: 31.9 C
  ID-3: /dev/sda vendor: Hitachi model: HUA723020ALA641 size: 1.82 TiB
    speed: 6.0 Gb/s serial: <filter>
  ID-4: /dev/sdb vendor: Hitachi model: HUA723020ALA641 size: 1.82 TiB
    speed: 6.0 Gb/s serial: <filter>
  ID-5: /dev/sdc vendor: Seagate model: ST1000DM003-1ER162 size: 931.51 GiB
    speed: 6.0 Gb/s serial: <filter>
  ID-6: /dev/sdd vendor: Crucial model: CT500MX500SSD1 size: 465.76 GiB
    speed: 6.0 Gb/s serial: <filter>
  ID-7: /dev/sde vendor: HGST (Hitachi) model: HTS725050A7E630
    size: 465.76 GiB type: USB rev: 3.0 spd: 5 Gb/s lanes: 1 serial: <filter>
  ID-8: /dev/sdf vendor: Western Digital model: WD140EDFZ-11A0VA0
    size: 12.73 TiB type: USB rev: 3.1 spd: 5 Gb/s lanes: 1 serial: <filter>
Partition:
  ID-1: / size: 475.35 GiB used: 419.62 GiB (88.3%) fs: btrfs
    dev: /dev/nvme0n1p3
  ID-2: /boot size: 973.4 MiB used: 807.4 MiB (82.9%) fs: ext4
    dev: /dev/nvme0n1p2
  ID-3: /boot/efi size: 598.8 MiB used: 19.3 MiB (3.2%) fs: vfat
    dev: /dev/nvme0n1p1
  ID-4: /home size: 475.35 GiB used: 419.62 GiB (88.3%) fs: btrfs
    dev: /dev/nvme0n1p3
Swap:
  ID-1: swap-1 type: zram size: 8 GiB used: 0 KiB (0.0%) priority: 100
    dev: /dev/zram0
Sensors:
  System Temperatures: cpu: 46.5 C mobo: 43.5 C gpu: amdgpu temp: 42.0 C
  Fan Speeds (rpm): N/A
Info:
  Memory: total: 48 GiB note: est. available: 45.92 GiB used: 4.21 GiB (9.2%)
  Processes: 482 Power: uptime: 13m wakeups: 0 Init: systemd v: 258
    default: graphical
  Packages: pm: rpm pkgs: N/A note: see --rpm pm: flatpak pkgs: 57
    Compilers: gcc: 15.2.1 Shell: Zsh v: 5.9 running-in: ptyxis-agent
    inxi: 3.3.40

@anotheruser

It seems that you’ve disabled the 2nd display in gnome-settings…

I’ve had to disable it as that is the display that is simply not getting a signal, although the OS thinks it is active (it also only shows a refresh rate of 30 Hz in the options, whereas it is a 60 hz display). I would get cursor stuttering and keyboard lag if I kept it on.

[computersavvy (Jeff V)]

Thank you for fixing the issue with those posts.

We have seen some cases where using both HDMI and DP on the same card has had problems.

Have you considered using a DP to HDMI cable and connecting both monitors to the DP ports on the GPU?

We have also seen cases where the integrated iGPU has caused issues with the main GPU even in desktop systems. Is it possible to disable the iGPU within bios to eliminate that possibility?

We have also seen cases where a 4k 60Hz monitor is restricted to 30Hz by either an older HDMI cable or the card itself which may be incapable of supporting 4k 60Hz when more than one monitor is attached.

[prosetheus (Paul Phoenix)]

Appreciate you taking the time to help me figure this out. I’m downloading the Fedora 44 update and will update in the hope that it might fix most of these issues.

There is something that has fundamentally become broken in the graphics drivers. I just tried playing back downloaded videos and most of files did not play, and those that did, had graphics artifacts.

I’ll report back if something changes after the update.

[computersavvy (Jeff V)]

@prosetheus

I just tried playing back downloaded videos and most of files did not play, and those that did, had graphics artifacts.

Have you performed the recommended changes for multimedia support as suggested here.?